Monday, 31 August 2015

How To - French Seams





Today I thought I'd do a bit of a tutorial on French seams. Plenty of people find them a bit intimidating, but they don't need to be. You do require accuracy though, so it helps to be able to sew straight.


Essentially, a French seam is two straight seams where the first seam is folded into the second. It works well on lightweight fabrics, particularly those which have a degree of transparency and need to look neat inside and out.

To begin, and to learn the particulars of your own machine, you need a ruler, pen, scissors and calico or muslin. Cut two rectangles to sew together. This is a practice piece only, once you know how to line it up you will not be drawing lines on your sewing.

When you use a French seam, you start with the wrong sides together. This is the opposite of other seams so keep it in mind.

Generally, a seam allowance is about 1.5cm or 5/8". It doesn't matter which you use (here's me with a metric ruler and an imperial mat!), the important part is to see how to get there in two steps. Draw the seam line on your top scrap of fabric.



Then draw another line halfway between the seam line and the edge.



This is where you get to know your machine. You want your first line of stitching to fall exactly on that middle line. So you need to find the position where that works. In all likelihood, this will be only a fraction to the side of the edge of the foot. You may find it works just on the edge of the foot!


Many modern machines allow you to adjust the position of the needle in a straight stitch using the width dial. Check your manual to see if this is the case with yours.
 If I put the dial on a 6, 


 
The needle will come down to the right of the centre line.
 I find with my machine, if I put the dial on '2' and line the fabric up with the edge of the foot, it will fall exactly where I want it to.
 Your machine may be slightly different, but once you figure it out, it will save lots of time and make French seams easier. 



After a bit of testing, I can easily sew accurately down that first line.

 I then trim half of that seam allowance off.
 And press it outwards.
 Fold it back and press it again. You should now have the right side together.

Sew the next seam with the edge of the fold in exactly the same position as you had the raw edge last time.

 Press it to the side.

 Turn it over and press down.
 If you have it in *exactly* the right position, your original pen line will be *just* on that stitching line. I can see my pen line just here.



 Now that I'm confident I can get the seams in the right position, I can try a test swatch on my real fabric. I used French seams on my lace dress. This works well for light weight all over lace. Having said that, it can sometimes distort a little because of the variation in bulk, so take care. It's *always* worth doing a test swatch.

I start with right sides facing outwards (wrong sides together). 

 And I sew down with needle and fabric in the same position as before.

 Snip off half off the seam allowance.

 Press outwards.
 Fold over and press again.
 And then sew again with needle and fabric in the same position.

 Press to the side.
 And there you have it.


As featured on this dress. Looks pretty neat huh?

So to answer the next question, can you use a French seam on a curve, like an armhole or a princess seam? 

Essentially yes. When you press the first time you need to take care to ensure it presses as neatly as possible and doesn't pucker. You may need to use a little steam to shape it. Some tight curves may pucker a little no matter what you do, so if in doubt do a test swatch first. If you find they do buckle, you could consider an alternative such as binding your seams for an equally neat finish.

Sunday, 30 August 2015

July Challenge - the Reveal!

Ok. It is August and I am just now putting my July challenge up. I know. 

Truthfully, I did actually get this done weeks ago. I just didn't get it photographed. It has a lot to do with this:


Which is another story for another day.

In any case, I chose to work with lace, as I hadn't worked with lace before. Rather, I haven't worked with non-stretch, all over lace. Which is on trend at the moment, it seems. So it was time.

I chose a beige corded lace and a bronze-gold polyester satin to go underneath it. The lace is a lot more beige but the flash made it appear almost white here.
I did a bit of research on it before I cut, although it was all pretty much what I expected. I used French seams on the side seams, and of course had to take the utmost care in cutting the skirt so that the scallops were in the right position.

Side Seam:


Vent. I was so proud of this. 


 And the dress!




The pattern is It is New Look 6184, which I've made before with the fuller skirt. 

I made it with a friends wedding in mind, and clipped the last threads about 40 minutes before departure. It was a bit close! But given the huge number of things on the go at the moment, completing a dress was such a boost. It made life feel a bit more normal! 


2015 Design / Inspiration Challenge - September

Hello all!

I know, blogging has been thin here lately. But things are coming together, so I expect to be keeping up this month!

September: Explore the textile styles of another culture. Create an item which reflects a technique or style of another culture. 

Perhaps you might like to look at Mexican embroidery, or Japanese shibori fabrics. You could look at different embroidery styles and colours used in Indian saris! Go on a world tour from your sofa, and see what you uncover. Share your photos and discoveries on facebook.

The item you create does not need to be finished. You might sketch something to illustrate a 'nod' to your research focus. Or recycle an existing item which includes these techniques into something new!